Model Number: PL6850

12/24 Volt 120A Flashing Power Supply and 120/60/40/10A Fleet Battery Charger

The PL6850 is designed to provide stable power, on demand up to 120 amps, to a vehicle electrical system to support module reprogramming. It is also designed specifically for fleet service battery charging with a maximum charge rate of 120 amps, to quickly and effectively bring 4- and 8-battery Group 31 packs back to full charge.

In power supply mode, the PRO-LOGIX PL6850 provides power to maintain vehicle electrical system voltage at a preset level, increasing its output in response to system load increases to maintain a stable power environment for successful reprogramming. It features a voltage output range of 13.1-14.9V, adjustable in 0.1V increments. allowing the operator to dial the output in exactly as specified by the supplier of the vehicle under service. It features fast load responsiveness for ultra-quick recovery from system demand increases. It also delivers its massive power with minimal voltage ripple (<100mV), providing a clean flow of power to the vehicle without risk of programming interference.

In charging mode, the PL6850 utilizes advanced microprocessor-controlled logic to precisely deliver a fully automatic charging routine designed to optimally charge and maintain each battery or battery pack serviced. The PL6850 features the ability to properly charge a wide variety of lead acid battery types, including Conventional, AGM, Spiral Wound, Start-Stop, Deep Cycle and Marine lead acid batteries, plus LiFEPO4 Lithium Batteries – enabling beneficial service of virtually any battery type installed in a vehicle. The PL6850 adapts its charging approach based on the needs of each battery or battery pack it services. Such adaptations can include activating a soft start mode on deeply discharged batteries, a battery repair mode on older/distressed batteries and temperature compensation when charging in extreme temperatures. It also incorporates numerous features to make charging safer for the operator and the vehicle/battery being charged, including over-voltage protection, reverse polarity protection, smart clamp technology and battery fault detection.

The unit includes a carry handle for easy transport around a shop or in and out of a mobile service vehicle.

  • 0-120A (12V), on demand, power supply mode to maintain system voltage
  • 0-60A (24V), on demand, power supply mode to maintain system voltage
  • Power supply mode provides optimal support for vehicle reprogramming and ADAS recalibration
  • Power supply mode has minimal voltage ripple (<100mV)
  • Power supply mode features Rapid Load Response (RLR) technology
  • 120/60/40/10A (12V) charging modes allow quick, efficient charging of all battery sizes
  • 60/40/10A (24V) charging modes allow quick, efficient charging of all battery packs
  • Properly charges Flooded, AGM, Spiral Wound, Deep Cycle, Marine Lead Acid Batteries
  • Properly charges Lithium Iron Phosphate (LiFePO4, LFP) Batteries
  • Forced Start Mode allows charging of totally dead (0.0V) batteries
  • Soft Start Mode enables safe chargiing of severely depleted batteries
  • Battery Repair Mode overcomes battery sulfation to restore reserve capacity
  • Reverse polarity protection and battery fault detection
  • Extra-long 13′ cable reach
  • Output cables are detachable (welding connectors) and field replaceable
  • PowerJaw clamps provide improved access to hard-to-reach batteries
  • PowerJaw clamps allow the hood to be closed (most vehicles) during ADAS calibration
  • Includes handle kit for each transport
  • Requires 20A service

Specifications

• Operating Voltage : 12/24V
• Operational Mode : Automatic
• 12V Charging Rates : 120/60/40/10A
• 24V Charging Rates : 60/40/10A
• Charging Phases : 7
• Battery Types Charged : Flooded, AGM, Spiral, Deep Cycle, Marine, LiFePO4 Lithium
• 12V Power Supply Output : 0-120A on Demand, 13.1-14.9V
• 24V Power Supply Output : 0-60A on Demand, 26.2-29.8V
• Maximum Voltage Ripple in PS Mode : 100mV
• Reverse Polarity Protection : Yes
• Battery Fault Detection : Yes
• Temperature Compensation : Yes
• Output Cable Length : 13′
• Output cable Gauge : #2AWG
• AC Input : ***Requires 20A service***
• Weight : 27 lbs.
• Warranty : 1 Year Limited
• UPC : 010271201167